has anyone replaced the console cover in a 92-96 corvette????
or know where to find the procedure ?
thanks for your help.
frank

has anyone replaced the console cover in a 92-96 corvette????
or know where to find the procedure ?
thanks for your help.
frank
Hello
The center console door has 4 torx head screws and a power wire that must be unplugged to remove it. Very easy.
David

Where are you getting your parts from, new/used?

thanks for the info in the console door. i am looking to replace the shifter surround in front of the console door....

anyone know the correct proceedure?

it is an automatic, does the shifter knob have to come off and how is that done????

thanks

frank taylor

new from corvette central

thanks for the procedure for the consold door.

are you familiar with the console in front of the console door, or shifter surround..?

do you know the procedure to remove that?

thanks

frank

thanks for the info in the console door. i am looking to replace the shifter surround in front of the console door....

anyone know the correct proceedure?

it is an automatic, does the shifter knob have to come off and how is that done????

thanks

frank taylor

Here's how you get the shift knob off (courtesy of Mid America):


Tools Required:
Small flat screwdriver, snap ring pliers, safety glasses
*Wear Safety Glasses during this installation, particularly in Steps 2 and 5.
1. Using the screwdriver, gently pry shift button and mounting clip up and out of shift knob to reveal shift lever rod.
2. *Looking down onto shift lever rod, use snap ring pliers to remove “C” snap ring. Keep one hand free to grasp the snap
ring immediately upon removal as this spring-steel snap ring is prone to taking flight!
3. Remove shift knob by pulling upward on knob. Note: Knob may be seated very tightly, continue to wiggle the knob
while pulling upward.
4. Install new shift knob, using heavy downward force to properly seat the new knob, so that snap ring channel on shift
lever rod is in view.
5. *Carefully reinstall snap ring. (Hint: Using snap ring pliers, spread snap ring apart then cup your hand around the
snap ring and shift knob opening in case the snap ring slips off the pliers.)
6. Reinstall button and mounting clip. With engine off, turn key to “Accessories” position to check operation of shifter in
all gears. (Do not start vehicle.) If shifter will not come out of Park, the shift knob is not seated, return to step 4.

Good luck!

Where are you getting your parts from, new/used?

Check out a couple of our sponsors

CorvetteSouth
http://www.corvettesouth.com/corvette-dash-104/dash-c4-84-96-106/

or Mid America Motorworks
http://www.mamotorworks.com/corvette?frame=3.3563

or Zip
http://www.zip-products.com/Zip/dept.asp?dept%5Fid=1197&gift=False&0=dept%2Easp%2Cdept%5Fid%3D1146%26menu%5Fid%3D%26T ree%3D%2CC4%20Interior&mscssid=AA629BB1A8B044CFB9E16395D49F5C96

I don't know if these urls work because they may have imbedded session ids. If they don't, just search on their sites.

Check out a couple of our sponsors

CorvetteSouth
http://www.corvettesouth.com/corvette-dash-104/dash-c4-84-96-106/

or Mid America Motorworks
http://www.mamotorworks.com/corvette?frame=3.3563

or Zip
http://www.zip-products.com/Zip/dept.asp?dept%5Fid=1197&gift=False&0=dept%2Easp%2Cdept%5Fid%3D1146%26menu%5Fid%3D%26T ree%3D%2CC4%20Interior&mscssid=AA629BB1A8B044CFB9E16395D49F5C96

I don't know if these urls work because they may have imbedded session ids. If they don't, just search on their sites.

Yes they worked just fine! :thumbsup: